KTU 2024 Scheme · Semester 3 · Program Core — Electrical and Electronics Engineering
Analog Electronics Lab (PCEEL308) Syllabus
Official KTU 2024 Scheme syllabus for Analog Electronics Lab, Semester 3, Program Core — Electrical and Electronics Engineering (Electrical and Electronics Engineering).
Course Code
PCEEL308
Credits
2
Teaching Hours
0:0:3:0 (L:T:P:R)
CIE Marks
50
ESE Marks
50
Exam Duration
2 Hrs 30 Min
Prerequisites
None
Semester
Semester 3
Course Objective
To design transistor and Op-amp circuits, and to simulate and implement the circuits in hardware.
Module-wise Syllabus
Module 1
Pre-lab: measurement of current, voltage, frequency and phase shift of signal in a RC network using oscilloscope; introduction to circuit simulation software. Clipping and clamping circuits using diodes. Basic RC circuits — high pass and low pass filters. RC coupled amplifier using BJT in CE configuration — measurement of gain, bandwidth and frequency response. Emitter follower amplifier. JFET amplifier — measurement of gain, bandwidth and frequency response. MOSFET amplifier. Design and testing of voltage regulators (Zener and series). Design and setup of inverting and non-inverting amplifiers. Op-amp circuits — scale changer, adder, integrator, differentiator. Precision rectifier using Op-amp. Op-amp oscillators — RC phase shift and Wien Bridge oscillator. Op-amp LC oscillators — Colpitts or Hartley oscillator. Waveform generation — square, triangular and sawtooth using Op-amps. Basic comparator and Schmitt trigger circuits using Op-amp (e.g. LM311). Active filters (high pass and low pass, one each). Instrumentation amplifier. Astable and monostable circuits using 555 IC. Introduction to PCB layout software.
Course Outcomes
- CO1Use various electronic instruments for conducting experiments.
- CO2Design and develop various electronic circuits using diodes and Zener diodes.
- CO3Design and implement amplifier and oscillator circuits using BJT and JFET.
- CO4Design and implement basic circuits using IC (Op-amp and 555 timers).
- CO5Simulate electronic circuits using any circuit simulation software.
- CO6Use PCB layout software for circuit design.
Assessment Pattern (CIE: 50 marks, ESE: 50 marks)
Continuous Internal Evaluation (CIE)
| Attendance | 5 |
| Preparation / Pre-Lab Work, Viva, Timely Record Completion (Continuous Assessment) | 25 |
| Internal Examination | 20 |
End Semester Examination (ESE)
Total 50 marks, 2 Hrs 30 Min. See the official KTU syllabus document for the exact Part A / Part B question pattern for this course.
Textbooks & Reference Books
Textbooks
- Introductory Electronic Devices and Circuits — Robert T Paynter, Boylestad R. L. and L. Nashelsky (Pearson Education, —)
- Electronic Devices and Circuit Theory — Donald A Neaman (Pearson Education / McGraw Hill Companies, —)
- Electronic Circuits: Analysis and Design — — (—, —)
Frequently Asked Questions
How many credits is KTU Analog Electronics Lab (PCEEL308)?
2 credits, with 0:0:3:0 (L:T:P:R) teaching hours per week, under the KTU 2024 Scheme.
How many modules are in the PCEEL308 syllabus?
1 modules.
What is the CIE and ESE mark split for this course?
CIE (Continuous Internal Evaluation): 50 marks. ESE (End Semester Examination): 50 marks, 2 Hrs 30 Min. Total: 100 marks.
What are the recommended textbooks for PCEEL308?
Introductory Electronic Devices and Circuits (Robert T Paynter, Boylestad R. L. and L. Nashelsky); Electronic Devices and Circuit Theory (Donald A Neaman); Electronic Circuits: Analysis and Design (—).
Is this syllabus specific to one branch, or common to others too?
This Semester 3 course is listed under Program Core — Electrical and Electronics Engineering at KTU under the 2024 Scheme — check the course header above for which branches it's common to.
Need help with KTU Analog Electronics Lab?
Learnizo offers live, 1-on-1 online tuition for KTU Electrical and Electronics Engineering subjects — matched to your exact module and semester.
Explore Engineering Tuition