KTU 2024 Scheme · Semester 3 · Program Core (PBL) — Electrical and Electronics Engineering

Analog Electronics (PBEET304) Syllabus

Official KTU 2024 Scheme syllabus for Analog Electronics, Semester 3, Program Core (PBL) — Electrical and Electronics Engineering (Electrical and Electronics Engineering).

This page compiles APJ Abdul Kalam Technological University's officially published 2024 Scheme syllabus for Electrical and Electronics Engineering, Semester 3, sourced directly from KTU's official website (ktu.edu.in). Learnizo is an independent online tuition platform and is not affiliated with, endorsed by, or officially connected to APJKTU. The university may revise syllabus content after this page was last updated — always cross-check with the official KTU source for the current, authoritative version.

Course Code

PBEET304

Credits

Teaching Hours

3:0:0:1 (L:T:P:R)

CIE Marks

ESE Marks

Exam Duration

2 Hrs 30 Min

Prerequisites

None

Semester

Semester 3

Course Objective

To enable students to design analog electronic systems using BJT, FET and Op-Amp.

Module-wise Syllabus

Module 1

9 contact hours

Review of Bipolar Junction Transistor — introduction to DC biasing, base bias, voltage divider bias. Common Emitter amplifier — AC concepts, role of coupling capacitors and emitter bypass capacitor, Common Emitter AC equivalent circuit, amplifier gain, calculation of amplifier gains and impedances using h-parameter equivalent circuit. Emitter follower amplifier. Power amplifiers — AC load line, RC coupled amplifiers, transformer coupled Class A amplifiers, Class B amplifiers (derivation of efficiency), Class AB amplifiers, Class C and Class D amplifiers.

Module 2

9 contact hours

Introduction to JFET — JFET biasing circuits, Common Source amplifier. Introduction to MOSFET — MOSFET construction, D-MOSFET, E-MOSFET, complementary MOSFET. Amplifier frequency response — basic concepts, BJT amplifier frequency response, FET amplifier frequency response. Feedback and oscillator circuits — feedback concepts, feedback connection types, practical feedback circuits. Oscillators — phase shift oscillator (expression of frequency oscillation), Wien Bridge oscillator, tuned oscillator circuits, crystal oscillator.

Module 3

9 contact hours

Introduction to Operational Amplifiers (Op-Amps) — operation overview, differential amplifiers and Op-Amp specifications (gain, CMRR and slew rate). Op-Amp circuits — inverting amplifiers, non-inverting amplifiers, summing and difference amplifiers, instrumentation amplifiers, differentiator and integrator circuits (practical circuits). Comparators — zero crossing and voltage level detectors, Schmitt trigger.

Module 4

9 contact hours

Active filters — Butterworth, Chebyshev and Bessel filters, low pass filter, high pass filter, band pass and notch filters, Butterworth. Waveform generation using Op-Amps — square, triangular and ramp generator circuits using Op-Amp, effect of slew rate on waveform generation. Timer 555 IC — internal diagram of 555 IC, astable and monostable multivibrators using 555 IC.

Course Outcomes

CO1Design BJT and FET amplifier circuits.
CO2Design oscillator circuits.
CO3Design and develop various OPAMP application circuits.
CO4Implement active filters.
CO5Implement an electronic hardware circuit for the solution of a real-time problem.

Assessment Pattern (CIE: 60 marks, ESE: 40 marks)

Continuous Internal Evaluation (CIE)

Attendance	5
Project	30
Internal Examination 1	12.5
Internal Examination 2	12.5

End Semester Examination (ESE)

Total 40 marks, 2 Hrs 30 Min. See the official KTU syllabus document for the exact Part A / Part B question pattern for this course.

Textbooks & Reference Books

Textbooks

Introductory Electronic Devices and Circuits — Robert T Paynter, Boylestad R. L. and L. Nashelsky (Pearson Education, —)
Electronic Devices and Circuit Theory — Donald A Neaman (Pearson Education / McGraw Hill Companies, —)
Electronic Circuits: Analysis and Design — — (—, —)

Reference Books

Fundamentals of Analog Circuits — Floyd T.L. (Pearson Education, —)
Op-Amps and Linear Integrated Circuits — Gayakward R. A. (PHI Learning Pvt. Ltd., —)
Electronic Devices and Circuits — David A Bell (Oxford Higher Education, —)
Linear Integrated Circuits — Choudhury R. (New Age International Publishers, —)

Frequently Asked Questions

How many credits is KTU Analog Electronics (PBEET304)?

4 credits, with 3:0:0:1 (L:T:P:R) teaching hours per week, under the KTU 2024 Scheme.

How many modules are in the PBEET304 syllabus?

4 modules, 36 total contact hours.

What is the CIE and ESE mark split for this course?

CIE (Continuous Internal Evaluation): 60 marks. ESE (End Semester Examination): 40 marks, 2 Hrs 30 Min. Total: 100 marks.

What are the recommended textbooks for PBEET304?

Introductory Electronic Devices and Circuits (Robert T Paynter, Boylestad R. L. and L. Nashelsky); Electronic Devices and Circuit Theory (Donald A Neaman); Electronic Circuits: Analysis and Design (—).

Is this syllabus specific to one branch, or common to others too?

This Semester 3 course is listed under Program Core (PBL) — Electrical and Electronics Engineering at KTU under the 2024 Scheme — check the course header above for which branches it's common to.

Need help with KTU Analog Electronics?

Learnizo offers live, 1-on-1 online tuition for KTU Electrical and Electronics Engineering subjects — matched to your exact module and semester.

Explore Engineering Tuition