Chat with us on WhatsAppCall Learnizo

KTU 2024 Scheme · Semester 3 · Program Core — Electronics and Communication Engineering

Analog Circuits (PCECT303) Syllabus

Official KTU 2024 Scheme syllabus for Analog Circuits, Semester 3, Program Core — Electronics and Communication Engineering (Electronics and Communication Engineering).

This page compiles APJ Abdul Kalam Technological University's officially published 2024 Scheme syllabus for Electronics and Communication Engineering, Semester 3, sourced directly from KTU's official website (ktu.edu.in). Learnizo is an independent online tuition platform and is not affiliated with, endorsed by, or officially connected to APJKTU. The university may revise syllabus content after this page was last updated — always cross-check with the official KTU source for the current, authoritative version.

Course Code

PCECT303

Credits

4

Teaching Hours

3:1:0:0 (L:T:P:R)

CIE Marks

40

ESE Marks

60

Exam Duration

2 Hrs 30 Min

Prerequisites

Introduction to Electrical and Electronics Engineering (GYEST104)

Semester

Semester 3

Course Objective

To introduce and verify the basic principles, operation and applications of various analog electronic circuits and devices, and to understand and analyze the design and working of amplifiers and their configurations.

Module-wise Syllabus

Module 1

10 contact hours

Wave shaping circuits: RC differentiating and integrating circuits, analysis of first order RC low pass and high pass filters for step input - rise time, bandwidth. Diode clipping and clamping circuits. BJT/MOSFET biasing: need for biasing, DC load line, operating point, BJT biasing (CE configuration) - fixed bias and voltage divider bias (design and analysis). MOSFET biasing.

Module 2

12 contact hours

BJT amplifiers: design of RC coupled CE amplifier, small signal analysis of the CE amplifier using the hybrid-pi model (low and mid frequency), the high-frequency hybrid-pi model of the BJT, Miller effect, high frequency response of the single stage CE amplifier, short circuit current gain, cut-off frequency and unity gain bandwidth fT. MOSFET amplifiers: design of the CS amplifier, small signal analysis using the hybrid-pi model (mid frequency only), small signal voltage gain, input and output impedance, CS stage with current source load and diode connected load. Multistage BJT amplifiers: types of multistage amplifiers, effect of cascading on gain and bandwidth. Small signal voltage gain, input and output impedance of the BJT cascode amplifier using the hybrid-pi model.

Module 3

11 contact hours

Feedback amplifiers: the general feedback structure, effect of negative feedback on gain, bandwidth, noise reduction and distortion. The four basic feedback topologies, analysis of discrete BJT circuits in voltage-series and voltage-shunt feedback topologies - voltage gain, input and output impedance. Oscillators: classification, criterion for oscillation, Wien bridge oscillator, Hartley and crystal oscillators (working principle and design equations of the circuits; analysis of the Wien bridge oscillator only required).

Module 4

11 contact hours

Power amplifiers: classification, transformer coupled class A power amplifier, push-pull class B and class AB power amplifiers, complementary-symmetry class B and class AB power amplifiers, class C and D power amplifiers - efficiency and distortion (no analysis required). Linear voltage regulators: types of voltage regulators - series and shunt, working and design, load and line regulation, short circuit protection and fold-back protection.

Course Outcomes

  • CO1Design wave shaping circuits using first order RC networks and diodes.
  • CO2Analyze single stage and multistage BJT amplifier circuits using equivalent models.
  • CO3Apply the principles of feedback in the design of oscillators.
  • CO4Design power amplifiers and voltage regulator circuits.

Assessment Pattern (CIE: 40 marks, ESE: 60 marks)

Continuous Internal Evaluation (CIE)

Attendance5
Assignment / Microproject15
Internal Examination 1 (Written)10
Internal Examination 2 (Written)10

End Semester Examination (ESE)

Total 60 marks, 2 Hrs 30 Min. See the official KTU syllabus document for the exact Part A / Part B question pattern for this course.

Textbooks & Reference Books

Textbooks

  • Electronic Devices and Circuit Theory — Robert Boylestad, Louis Nashelsky (Pearson, 11th edition, 2015)
  • Microelectronic Circuits — Adel S. Sedra, Kenneth C. Smith (Oxford University Press, 6th edition, 2013)
  • Electronic Circuits and Devices — Theodore F. Bogart, Jeffrey S. Beasley, Guillermo Rico (Pearson Education India, 6th edition)

Reference Books

  • Fundamentals of Microelectronics — Behzad Razavi (Wiley, 2nd edition, 2015)
  • Electronic Devices and Circuits — David A. Bell (Oxford University Press, 5th edition, 2008)
  • Electronic Circuits Analysis and Design 1 — D. Meganathan (Yes Dee Publishing, 1st edition)

Frequently Asked Questions

How many credits is KTU Analog Circuits (PCECT303)?

4 credits, with 3:1:0:0 (L:T:P:R) teaching hours per week, under the KTU 2024 Scheme.

How many modules are in the PCECT303 syllabus?

4 modules, 44 total contact hours.

What is the CIE and ESE mark split for this course?

CIE (Continuous Internal Evaluation): 40 marks. ESE (End Semester Examination): 60 marks, 2 Hrs 30 Min. Total: 100 marks.

What are the recommended textbooks for PCECT303?

Electronic Devices and Circuit Theory (Robert Boylestad, Louis Nashelsky); Microelectronic Circuits (Adel S. Sedra, Kenneth C. Smith); Electronic Circuits and Devices (Theodore F. Bogart, Jeffrey S. Beasley, Guillermo Rico).

Is this syllabus specific to one branch, or common to others too?

This Semester 3 course is listed under Program Core — Electronics and Communication Engineering at KTU under the 2024 Scheme — check the course header above for which branches it's common to.

Need help with KTU Analog Circuits?

Learnizo offers live, 1-on-1 online tuition for KTU ECE subjects — matched to your exact module and semester.